ATA8743-PXQW【PDF 94/238 页】MCU W/TRANSMITTER ASK/FSK 24QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录52

90页 91页 92页 93页 [94页]95页 96页 97页 98页

9152BINDCO02/10

ATA8743

20.6.1

Compare Output Mode and Waveform Generation

The Waveform Generator uses the COM0x1:0 bits differently in Normal, CTC, and PWM modes.

For all modes, setting the COM0x1:0 = 0 tells the Waveform Generator that no action on the

OC0x Register is to be performed on the next Compare Match. For compare output actions in

the non-PWM modes refer to Table 20-2 on page 100. For fast PWM mode, refer to Table 20-3

on page 100, and for phase correct PWM refer to Table 20-4 on page 101.

A change of the COM0x1:0 bits state will have effect at the first Compare Match after the bits are

written. For non-PWM modes, the action can be forced to have immediate effect by using the 0x

strobe bits.

20.7 Modes of Operation

The mode of operation, i.e., the behavior of the Timer/Counter and the Output Compare pins, is

defined by the combination of the Waveform Generation mode (WGM02:0) and Compare Output

mode (COM0x1:0) bits. The Compare Output mode bits do not affect the counting sequence,

while the Waveform Generation mode bits do. The COM0x1:0 bits control whether the PWM out-

put generated should be inverted or not (inverted or non-inverted PWM). For non-PWM modes

the COM0x1:0 bits control whether the output should be set, cleared, or toggled at a Compare

Match (See Modes of Operation on page 94).

For detailed timing information refer to Figure 20-8 on page 98, Figure 20-9 on page 99, Figure

20-10 on page 99 and Figure 20-11 on page 99 in Timer/Counter Timing Diagrams on page

98.

20.7.1

Normal Mode

The simplest mode of operation is the Normal mode (WGM02:0 = 0). In this mode the counting

direction is always up (incrementing), and no counter clear is performed. The counter simply

overruns when it passes its maximum 8-bit value (TOP = 0xFF) and then restarts from the bot-

tom (0x00). In normal operation the Timer/Counter Overflow Flag (TOV0) will be set in the same

timer clock cycle as the TCNT0 becomes zero. The TOV0 Flag in this case behaves like a ninth

bit, except that it is only set, not cleared. However, combined with the timer overflow interrupt

that automatically clears the TOV0 Flag, the timer resolution can be increased by software.

There are no special cases to consider in the Normal mode, a new counter value can be written

anytime.

The Output Compare Unit can be used to generate interrupts at some given time. Using the Out-

put Compare to generate waveforms in Normal mode is not recommended, since this will

occupy too much of the CPU time.

20.7.2

Clear Timer on Compare Match (CTC) Mode

In Clear Timer on Compare or CTC mode (WGM02:0 = 2), the OCR0A Register is used to

manipulate the counter resolution. In CTC mode the counter is cleared to zero when the counter

value (TCNT0) matches the OCR0A. The OCR0A defines the top value for the counter, hence

also its resolution. This mode allows greater control of the Compare Match output frequency. It

also simplifies the operation of counting external events.

The timing diagram for the CTC mode is shown in Figure 20-5 on page 95. The counter value

(TCNT0) increases until a Compare Match occurs between TCNT0 and OCR0A, and then coun-

ter (TCNT0) is cleared.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式